Why Does My Rolls Royce Phantom Key Fob Not Work?
The Rolls-Royce Phantom conveys wealth and prestige. Its massive waterfall grille and classic upright proportions are instantly recognizable. It is also among the most expensive automobiles around the globe.
A rolls royce phantom key fob can cease to function for a variety of reasons. The most common cause is a dead coin battery, but it can also be caused by water damage or receiver module issues.
Battery
The most common reason for the Rolls-Royce Phantom key fob not functioning is the dead battery inside. However, it is important to note that the key fob also can stop functioning due to a variety other causes, such as damaged buttons, water damage or a bad battery contact signal interference, or unpaired keys that require changing the program. If your key fob stops working, you might want to speak with locksmith. A locksmith can identify the problem quickly and provide the solution quickly.
To ensure that the battery stays functioning, it must be protected from moisture and dirt. This is the reason why it is recommended that you always use a waterproof case for your key fob when driving. It is also recommended to remove battery from key fob before cleaning or washing it. Furthermore, the chip inside the key fob is extremely sensitive to water and should not be exposed to soapy or salty water. If the key fob is likely to be exposed to water, you can use electronic cleaner or isopropyl to avoid damage.
The battery pack of the Phantom EE features a number of innovations that set it apart from traditional power systems used in other luxury vehicles. A "power reserve dial" for instance it has been added to the dashboards to inform the driver of the vehicle's current energy condition. This is a brand new design feature that is designed to challenge the traditional paradigms of car design and highlight the potential for alternative drive-train technology.
This electric powertrain has the advantage of allowing charging without the need for a physical connection between car and charging station. This is accomplished by using induction, a system that involves the transfer of power over two surfaces: an induction pad on the ground, and an energy transfer module that is located under the battery pack.
The process of recharging takes place in two stages, and has a capacities of 13.5kW per phase and a total capacity of 71kWh. This makes it the largest passenger car battery in the world. In addition the Phantom EE is fitted with three separate charger units that allow for charging in three phases and single-phase and regenerative braking.
Contacts
If your Rolls Royce Phantom remote key fob has stopped working it could be caused by the battery being dead or worn buttons. This issue is usually easy to fix. You can also try reprogramming the key fob or replacing the 12 volt battery. If the problem persists the receiver module may be faulty. The remote keyless system as well as other electronics onboard use the receiver module to communicate with each other via radio signals. If the receiver module develops a fault, it will stop communicating with the key fob and other onboard electronics.
If you're having problems with your key fob, make sure that the battery contacts are clean and dry. The retaining clips made of metal hold the button cell in place and complete the circuit, and they can be damaged by dirty or wet hands. If the battery is worn out you must replace it with a brand new one that has the same size and voltage. If you replace the battery, make sure to clean the surfaces of contact with the use of rubbing alcohol or electronic cleaner before making the key fob.
The key fob in the Rolls Royce Phantom is equipped with an electronic chip that sends signals to the remote keyless system receiver module. This module then translates these signals into commands the car can comprehend and act on. This is how your car will know that you are attempting to open the doors or retract the famous "flying lady" Hood ornament into the grille.
If the key fob was exposed to water, immediately remove it from the vehicle and clean the electronic chip with isopropyl alcohol, or electronic cleaner. If you don't, the chip will likely be damaged.
Water damage
The key fob is constructed with rubber seals that prevent the chip inside from being exposed to water. This makes it resistant to splashes and rain but not the kind of deep water immersion that could happen if you drop your key into a puddle or drop it in the ocean. If rolls royce car key price TheKeyLab gets wet the chip might be fried. You will need to replace it.
Even if you've not dropped your key fob in water, but it's soaked by a wet dog, washing machine or even soapy handwashing, don't despair because your roll royce phantom key fob could be usable. You can save money by following a few easy steps.
First, you must dismantle the key fob and thoroughly dry it. If you can, remove the battery and use compressed air to remove any excess moisture. After you've done this, let it dry out for a few days and try it again.
If your key fob is prone to get wet, consider buying an waterproof case to shield it from accidents. It's also recommended to keep an extra key in your pocket so that you don't have to wait for the fob to dry out.
In certain situations it is possible that your Rolls Royce Phantom key fob could stop working due interference or an unresponsive 12 volt battery. This problem is often caused by objects, bad weather conditions, or transmitters operating on the same frequency your remote.
Keep your key fob away from these sources. If you can't avoid these sources of interference, try shifting your car to a different location or reprogramming your remote. If you're unable to fix the issue, it's recommended to speak with an expert technician. They can identify the issue and determine if the issue is an electrical or mechanical fault.
Reprogramming
The key fob that you have in your Rolls Royce Phantom is an essential component of your vehicle's security system. It transmits commands from the key fob to the receiver module which then sends the commands to the central locking mechanism of the vehicle. It can be a hassle and expensive if your key fob stops functioning. There are a few basic ways to make sure your key fob is working again.
The first thing to determine is whether the coin battery in the key fob is dying. This is the most common reason for Phantom key fobs not locking or unlocking. There are usually indications of deterioration, like an increase in range. Replace the battery by an alternative one that has the same size, voltage and specifications. Also, make sure the metal retaining clips that keep the battery in place aren't loose.
Another possible cause is water damage. The key fob is equipped with rubber seals to prevent water from getting to the electronic chip inside, but should it be immersed in soapy or salty water, the seals could break down. If this happens, you should remove the battery and clean it using isopropyl alcohol or an electronic cleaner. Dry it thoroughly before putting it back into the fob.
If the key fob still isn't working, it could be a sign the receiver module has suffered a malfunction. Connecting a diagnostic scanner on the Phantom's dashboard to the OBD port is the best method to determine the issue. The scanner will request details about your vehicle, including the year, model and engine type. You'll also have to enter the code for your key fob.
Signal interference is a second possible reason. This could be caused by objects, weather conditions or transmitters that operate on the same frequency. The remote control will still work when you're close to the Phantom, but it won't unlock or lock from an extended distance. This can be resolved by removing objects that may be blocking the signal, or by moving the Phantom further away from the transmitters.